Imagen1.jpg_thumb90

Felipe Manuel Castro Cerda

Académico

Universidad de Santiago de Chile

Santiago, Chile

Líneas de Investigación


Physical metallurgy and phase transformations in steels Microstructural characterization and texture analysis

Educación

  •  Materials Science, UNIVERSITEIT GENT. Bélgica, 2017

Experiencia Académica

  •   Asistente de Investigación Part Time

    UNIVERSIDAD DE SANTIAGO DE CHILE

    Ingeniería

    Santiago, Chile

    2017 - 2017

  •   Académico Full Time

    UNIVERSIDAD DE SANTIAGO DE CHILE

    Ingeniería

    Santiago, Chile

    2018 - At present

Experiencia Profesional

  •   Heat-treatment supervisor Full Time

    Equipos Mineros Ltda.

    Chile

    2009 - 2012

Formación de Capital Humano


Supervised undergraduate theses

Title: Estudio de cortes térmicos en piezas de acero al carbono
Author: Gerardo Romo
Institution: Universidad de Santiago
Year: 2018

Co-supervised undergraduate theses

Title: Puesta en marcha de un horno simulador de recocido mediante calentamiento ultra rápido
Author: Fabián Durán
Institution: Universidad de Santiago
Year: 2018

Title: Puesta en marcha de un horno simulador de recocido mediante calentamiento ultra rápido
Author: Fabián Durán
Institution: Universidad de Santiago
Year: 2018

Title: Efecto de las caracteristicas microestructurales de la perlita sobre las constantes elásticas medidas por ultrasonido
Author: Jorge Carreño, Ricardo Piña
Institution: Universidad de Santiago
Year: 2018

Title: Evaluación de una fundición ASTM A532 IID aleada con 0.8 %Nb para rotores de áridos
Author: Luis Astorga
Institution: Universidad de Santiago
Year: 2018

Title: Estudio y caracterización de un acero con comportamiento TRIP producido por calentamiento ultra rápido
Author: Bruno Arroyo, Jorge Ñancupil
Institution: Universidad de Santiago
Year: 2019

Title: Determinación de la relación entre constantes elásticas obtenidas por ultrasonido y las componentes de texturas obtenidas en un acero ASTM A36
Author: E. Sepúlveda, M. Sotelo
Institution: Universidad de Santiago
Year: 2019



 

Article (24)

Balanced Constrained Carbon Equilibrium Accompanied by Carbide Precipitation
Isothermal Phase Transformations in a Low Carbon Steel During Single and Two-Step Partitioning (vol 51, pg 1506, 2020)
Behavior of ultrafast annealed advanced high strength steels under static and dynamic conditions
Effect of Boron in the Coarsening Rate of Chromium-Rich Carbides in 9%-12% Chromium Martensitic Creep-Resistant Steel: Experiment and Modeling at 650 degrees C
Effect of the austenitizing parameters on the microstructure and mechanical properties of 75Cr1 tool steel
Isothermal Phase Transformations in a Low Carbon Steel During Single and Two-Step Partitioning
Modeling the Mechanical Response of a Dual-Phase Steel Based on Individual-Phase Tensile Properties
The influence of the heating rate on the microstructure and mechanical properties of a peak annealed quenched and partitioned steel
Atomic-scale investigations of isothermally formed bainite microstructures in 51CrV4 spring steel
Exploring the microstructure and tensile properties of cold-rolled low and medium carbon steels after ultrafast heating and quenching
Novel experimental method to determine the limit strain by means of thickness variation
Effects of heat treatment on morphology, texture, and mechanical properties of a MnSiAl multiphase steel with TRIP behavior
Temperature Dependence of the Microstructure and Mechanical Properties of a Twinning-Induced Plasticity Steel
‘Flash’ Annealing in a Cold-Rolled Low Carbon Steel Alloyed With Cr, Mn, Mo, and Nb: Part I - Continuous Phase Transformations
“Flash” Annealing in a Cold-Rolled Low Carbon Steel Alloyed with Cr, Mn, Mo, and Nb: Part II-Anisothermal Recrystallization and Transformation Textures
Advanced High Strength Steels: Improved Properties by Design of Textures and Microstructures
Austenite formation in 0.2% C and 0.45% C steels under conventional and ultrafast heating
The Effect of Heating Rate on the Microstructure of a Soft-Annealed Medium Carbon Steel
The Effect of Heating Rate on the Recrystallization Behavior in Cold Rolled Ultra Low Carbon Steel
The effect of the pre-heating stage on the microstructure and texture of a cold rolled FeCMnAlSi steel under conventional and ultrafast heating
Microstructure, texture and mechanical properties in a low carbon steel after ultrafast heating
The Effect of Ultrafast Heating in Cold-Rolled Low Carbon Steel: Recrystallization and Texture Evolution
The Effect of Ultrafast Heating on Cold-Rolled Low Carbon Steel: Formation and Decomposition of Austenite
Characterization of dual-phase steels obtained by hot-rolling

ConferencePaper (1)

Static and dynamic response of ultra-fast annealed advanced high strength steels

Proyecto (4)

Development of new Ag-SnO2-ZnO materials for electrical contact applications by mechanical alloying, hot mechanochemical processing and hot pressing
NOVEL APPROACH TOWARDS THIRD GENERATION ADVANCED HIGH STRENGTH STEELS=> COMBINING ULTRAFAST HEATING AND QUENCHING & PARTITIONING PROCESSES
INCREASING THE DRAWABILITY OF TRIP-AIDED STEELS BY CONTINUOUS ANNEALING
ESTUDIO DE LA RESPUESTA A EMBUTICION DE ACEROS DUAL PHASE RECOCIDOS EN CONTINUO.
26
Felipe Castro

Académico

Metalurgia

Universidad de Santiago de Chile

Santiago, Chile

8
Alberto Monsalve

ACADEMICO

INGENIERIA METALURGICA

UNIVERSIDAD DE SANTIAGO DE CHILE

Santiago, Chile

3
Alfredo Artigas

profesor Titular

Ingeniería Metalurgica

UNIVERSIDAD DE SANTIAGO DE CHILE

Santiago, Chile

1
Andres Jaramillo

Profesor Asistente

Ingeniería Mecánica

Universidad de La Frontera

Temuco, Chile

1
David Rojas

Docente

Materiales

Universidad de Cocnepcion

Concepción, Chile

1
Sergio Yanez

Profesor Asistente

Ingeniería en Obras Civiles

Universidad de Santiago de Chile

Santiago, Chile

1
Juan Sanhueza

Profesor Asistente

Departamento de Ingeniería Materiales

Universidad de Concepción

Concepción, Chile

1
Diego Celentano

Full Professor

Mechanical and Metallurgical Engineering

Pontificia Universidad Católica de Chile

santiago de chile, Chile

1
Juan Pina

Profesor Asistente

Ingeniería en Obras Civiles

Universidad de Santiago de Chile

Santiago, Chile

1
Carlos Guzmán

Profesor Asistente

Ingeniería en Obras Civiles

Universidad de Santiago de Chile

Santiago, Chile

1
Bernd Schulz

Profesor de Excelencia

Metalurgia

USACH

STGO, Chile

1
FLAVIO DE BARBIERI

ACADEMICO JORNADA COMPLETA

DIMM

UNIVERSIDAD TECNICA FEDERICO SANTA MARIA

Valparaiso, Chile

1
Cristobal Montalba

Docente/Investigador

Tecnologías Industriales

Universidad de Talca

Curicó, Chile